ショッピングカート:
カート内商品数 0 アイテム
 

ImmersionRC Tramp HV 5.8GHz FPV Video Transmitter V2 (Internatio

5,890円

ImmersionRC Tramp HV 5.8GHz FPV Video Transmitter V2 (International version)

TrampHV Video Txは、スリムな17mmサイズ!わずか4グラムの重量!
大きさは31 x 20mmで最小、最軽量、高出力、高電圧のA / Vトランスミッターです!
このサイズでも、従来のImmersionRCのトランスミッターと同じくVフィルター付きBEC内蔵でカメラに5Vを供給できます。
入力電圧は
2s-4sでHV対応です
ピットモードをサポート!レースなどでとても便利です!

Features

 

  • Smallest direct LiPo powered vTx in the business.
  • TNR Touch-free wand control (optional)
  • Traditional button+LED control of frequency and power
  • 1mW -> 600mW linear power control
  • All 40 standard channels
  • Built-in thermal protection
  • Factory power normalization
  • Glitch-Free frequency changes
  • Micro-power pit mode
  • Additional channels for race events (Race Wand only)
  • Retail regional locking without opening package

 

Specifications

 

  • Dimensions: L=32mm x W=14mm x H=5mm
  • Weight: 4g (Tx only, without SMA cable)
  • Power Output: Programmable, 1mW to > 600mW
  • Channels: 48 standard, arbitrary using race wand
  • RF Impedance: 50 ohms
  • RF Connector: U.FL
  • AV Connector: JST-GH, 6 pin, locking
  • TNR Connector: JST-GH, 4 pin, locking
  • Audio: Mono, Subcarriers on 6.0 and 6.5MHz (cloned)
  • Modulation: FM, Audio and Video
  • Pit Frequency: User/Race Organizer Definable
  • Video Impedance: 75 ohms
  • Power Requirements: 2s-6s HV Lipo (6s as of March 2017)
  • Power Consumption:  ~4W max. @ 600mW, ~1.9W @ 200mW

 

Downloads

 

Download the TrampHV User Manual

 

Pit Mode

 

The ImmersionRC TrampHV was the first transmitter to support Pit Mode, which was introduced successfully at the FPVAirShow in France. Pit mode transmits a tiny amount of power on a pre-defined frequency to allow for quad setup at a race event without disrupting the show. Pit mode on the TrampHV is a little different than other offerings, being controlled by race directors transparently at drone races. A race director can stay legal by choosing a pit frequency authorized for use at the event, which can be different for events in different regions. Programmed at the event using the Touch’n’Race wand.

 

Touch ‘n’ Race for Race Directors

 

Touch’n’Race, a patent-pending technology which helps both the casual racer, and race directors alike.
Transmitters are placed in Race mode upon arrival at a race event, and remain in that mode until the event is over. Race directors can, without powering up a model, define the frequency and power output of the transmitter, in 5 seconds flat before a race starts.
As soon as the race is over, and the battery disconnected, the TrampHV reverts to it’s race-director defined mode. Massively decreased inter-heat times are possible with this technology, meaning more practice runs, more qualifiers, and races which start and finish on-time (a rarity in the world of drone racing today). More importantly, the chances of a race being disrupted by an accidental power-up in the pits are eliminated, a dream for race organizers.

 

Touch ‘n’ Race for Pilots

 

Why let race directors have all the fun?. The personal TNR wand* avoids dip-switch hell even in the local park. Touch-free programming of video transmitters before you launch, eliminating frequency collisions, eliminating the ‘what channel was I on last’ question, and allowing power levels to be modified between flights to adapt to local conditions. Note that the wand is not required to operate the transmitter. A traditional button + LED user interface may also be used to program channel, band, and power level.

 

Thermally Protected

 

We have all experienced long delays at the starting grid before starting a race. No airflow over the electronics and video transmitters overheating. Most video transmitters (even the higher end units) have no thermal protection whatsoever and will happily cook themselves and prematurely fail. The TrampHV is a little different. It constantly monitors the temperature of the Tx, and gracefully reduces power output to increase battery life and protect the transmitter. As soon as the props start spinning, it detects the temperature reduction and quickly boosts power output.

 

Screened for Protection, and Certification

 

The only Video Transmitter in this size and weight class with a fully screened RF deck, providing protection against dust, dirt and knocks, while ensuring smooth sailing through the RTT&E certification process. An optional plastic case can be easily installed to increase this protection even further, without adding excessive size and weight.

 

LapRF Certified

 

The TrampHV was designed alongside ImmersionRC’s RF Lap Timing system, with certified compatibility. LapRF eliminates the need for transponders on the quad for lap timing, and instead uses the energy emitted by the 5.8GHz transmitter on the quadcopter. Two LapRF versions will be available, a 16-channel race version for larger events, and a personal system no larger than a hockey puck for personal use (up to 4 pilots). Both versions sport a wireless connection to a smart phone for timing and configuration.

 

Anti-Glitch

 

Another first, introduced by ImmersionRC at FPVAirRace, is technology which allows video transmitters to power up cleanly on their assigned channel without wiping out neighboring channels. Gone are the days when your fellow pilots need to hover safely why you power up beside them. This technology enables asynchronous race starts, where pilots join a race at any time without creating any interference.

 

Calibrated Power

 

Each and every TrampHV is factory calibrated to ensure precise power outputs, especially at the critical low-power race levels. No more cross-talk from 25mW transmitters which are instead emitting 200mW!, or worse, 25mW transmitters which emit much lower power levels. No more RF lap timing issues caused by pilots running wildly different power levels.


売り切れ
  • モデル: IM-trump-hv
  • 重量: 0.2kg
  • 0 在庫量




この商品は2018年04月09日(月)に登録されました。